Hydroponics-grow-plants-grow-lights-room-box-herb-garden-grow-shop-hydro-plant-ihidrousa-ihidro-supplies-gardeners-gardening

We all have a plant or two that are favorites and we want to continually harvest from. Whether you are taking cuttings from your outside garden or want more harvesting from your indoor garden, it's essential that you go about it correctly.

Before you even start considering a constant supply of cuttings, you must start with a mother or donor plant. This plant should always be productive or abundant and healthy.

Choose a plant to grow that offers as many nodes as possible. An abundance of nodes will assure the plant's stress will remain low when you are making your cuttings. Also, be sure your mother plant is well watered at the time of cloning, as dehydration can be a serious problem for the clones.

Cutting Your Branches:

You are going to cut the side of the branch, approximately 6 inches long. Then emerge the cutting under water and make a second cut about two to three inches in from the cutting's end. This is to prevent an air bubble entering the inside tissue of your clone.

Once you have completed the above step, dip the clone in the rooting gel and place it in your choice rooting medium.

Rooting Gel:

A rooting gel is better than a powder because the gel will stick to the end of the clone and not wash off when watered. The gel also serves as a capping element for the end of the clone, preventing embolisms. IBA is a hormone that generates essential root formation.

Please Note: Never dip your clones into the bottle of gel. This could contaminate the gel for any future use. Pour a sufficient amount into another glass container or place on wax paper.

Rooting Medium:

Rockwood and peat plugs seem to be the favorites for root mediums. You can see the development of the roots without having to tug on the clones to find out if they are taking root.

Minimize Moisture Loss:

You want to make sure your cuttings have a high level of humidity by using a flat cover to maximize the moisture. This is important because moisture is lost during transpiration Transpiration is the passage of water through a plant from the roots and then into the atmosphere.

If you cuttings have large leaves, cut them in half to decrease moisture loss.

The Hydroponic Cloning System:

If you are planning on having many clones on a regular basis, you might want to seriously consider buying a hydroponic cloning system. These systems offer a much higher rate of returns on your rooting success. These systems do not require a medium to plant the cuttings into before they root. Clones can either remain in these systems or can be planted in soil afterwards.

The two most popular systems:

Bubble Cloners:

You can make a bubble cloner very easily, all you need are:

  • One three to five gallon bucket
  • One Air Pump
  • One Stone
  • Some 2-Inch Net Cups
  • Neoprene Collars

Maintain a water level that is just under the net cups in order for your stems to remain moist.

Aeroponic Cloners:

Although these systems are somewhat expensive, they offer the easiest and most efficient way to clone your plants. You should see visible root growth within 8 to 10 days and in some cases as briefly as 5 days.

You can then transplant your rooted cuttings into soil, a hydroponic medium or a soilless medium. Whatever you choose!

Cleaning:

It is very important that you keep your cloning system clean. This will prevent the chance of bacteria and fungi developing, which will rot your clone's stems very quickly.

Between uses, run H2O2 through the system for a few hours. Should you find areas that are not cleaning well, take a brush and dilute H2O2 or a bleach solution and apply to the stubborn spots. This will also insure there are no micro-organisms remaining in the system.

To Sum It Up:

Make sure your 6 inch cuttings have few large leaves and maintain a temperature of 75 degrees. Provide anywhere from 60% to 80% humidity.

Use cloning gels that contain micro nutrients with IBA hormones to hasten root development. Water your cuttings with a light, liquid fertilizer that is made specifically for clones and seedlings.

Cloning plants can be a great way to have extra harvests throughout the year. If you are new to cloning, ask your local nursery for assistance. If you are interested in purchasing a hydroponic cloning system, check with a nursery that specializes in them.